混凝土自上料攪拌車行車與保養兩不誤
混凝土自上料攪拌車是現在工程建設不可或缺的工程車輛，特殊的工作環境造就了不一樣的它，下面隨混凝土自上料攪拌車廠家一起來看看攪拌車的保養。
The concrete self loading mixer is an indispensable engineering vehicle for engineering construction. The special working environment has created a different one. Now let's join the manufacturer of the concrete self loading mixer to check the maintenance of the mixer.
1、初次工作50小時緊固前臺U型螺栓、前臺與減速機底座連接螺栓、減速機法蘭與攪拌筒連接螺栓、托輪與機架的緊固螺栓及托輪鎖緊螺母；以后每月定期檢查一次。
1. Tighten the U-shaped bolts of the front desk, the connecting bolts between the front desk and the reducer base, the connecting bolts between the reducer flange and the mixing drum, the fastening bolts between the supporting wheel and the frame and the locking nuts of the supporting wheel after the first 50 hours of work; After that, it shall be checked regularly every month.
2、各緊固螺栓在出廠前都經過嚴格檢驗，均達到要求的緊固力矩，對于因使用而發生的松動，要及時緊固，恢復其規定力矩，嚴重損壞的要及時更換。
2. All fastening bolts shall be strictly inspected before delivery and meet the required tightening torque. Looseness due to use shall be tightened in time to restore the specified torque, and those seriously damaged shall be replaced in time.
3、每次在車輛發動之前，檢查液壓油冷卻器和減速機的油位，保證油位指示在目視范圍內；液壓系統應經常保持清潔和密封，以免塵粒和水份等污染系統液壓油，造成系統不能正常工作或損壞。
3. Before starting the vehicle each time, check the oil level of the hydraulic oil cooler and reducer to ensure that the oil level indication is within the visual range; The hydraulic system should always be kept clean and sealed to prevent dust particles and moisture from polluting the hydraulic oil of the system, causing the system to fail to work normally or be damaged.
4、每天行車前檢查托輪與滾道的結合面潤滑油是否干澀，應及時補充，保持良好的潤滑效果。
4. Before driving every day, check whether the lubricating oil on the joint surface of the supporting wheel and the raceway is dry, and replenish it in time to maintain a good lubricating effect.
5、至少每月打開一次托輪護罩，清理里面的污物；通過托輪上的油嘴，向托輪內注入潤滑油脂。
5. Open the supporting wheel shield at least once a month to clean the dirt inside; Inject lubricating grease into the supporting roller through the oil nozzle on the supporting roller.
6、保證傳動軸至少每月潤滑一次。
6. Ensure that the transmission shaft is lubricated at least once a month.
7、經常性檢查管路及液壓設備的緊固螺栓是否有松動，保障設備的安全，必要時更換螺栓。
7. Regularly check whether the fastening bolts of the pipeline and hydraulic equipment are loose to ensure the safety of the equipment. Replace the bolts if necessary.
8、注意觀察散熱器上的真空表指示，當指針位于紅色區域時，應及時更換濾芯，對于使用一年以上的濾芯，即使指針不在紅色區域，也應該更換；要使用同一生產廠家的產品。
8. Observe the indication of the vacuum gauge on the radiator. When the pointer is in the red area, replace the filter element in time. For the filter element that has been used for more than one year, replace it even if the pointer is not in the red area; Use products from the same manufacturer.
9、至少每隔6個月檢查液壓泵、液壓馬達及油路的密封性能。
9. Check the sealing performance of hydraulic pump, hydraulic motor and oil circuit at least every 6 months.
10、及時檢查散熱器的風扇和溫控開關的性能，保證其正常工作,油溫一般在60℃左右時風扇會(huì )自動打開。
10. Timely check the performance of the radiator fan and temperature control switch to ensure their normal operation. Generally, when the oil temperature is about 60 ℃, the fan will turn on automatically.
所以說攪拌車司機不僅要會(huì )開攪拌車還要會(huì )“養”它，以上十點就是為您推薦的相關問題內容了，您可以作為參考使用，更多相關信息就來我們網站http://www.tanxudong.cn咨詢了解吧！
So the mixer driver should not only be able to drive the mixer but also be able to "maintain" it. The above ten points are recommended for you. You can use them as reference, and more relevant information will come to our website http://www.tanxudong.cn Ask and understand!
